Wavebeam 5AC

5GHz 23dBi ipMax AC Gigabit Outdoor CPEModel: iLBE-5AC
  • 5GHz 11AC 867Mbps
  • 23dbi directional antenna
  • One Gigabit Ethernet Port
  • IP65 waterproof enclosure
  • 6000V Lightning Protection
  • AP,Station,WISP operating mode supported
iLBE-5AC Long Range Outdoor CPE is designed to PtP&P2MP solutions for video surveillance transmission and wireless broadband access. Adopts of 11ac wireless technology and gigabit ethernet Port design, the maximum throughput for ptp connection could be up to 450Mbps. It features with 23dBi dual polarization directional antenna to provide an efficient way to pick up and maintain a stable long range range connection.

25km+ transmission Range

iLBE-5AC adopts of independent external power amplifier and 23dBi directional antenna to provide an efficient way to pick up and maintain a stable signal for a wireless network up to 25km.

P2P Connection Throughput up to 450+Mbps

iLBE-5AC adopt of 11AC wave2 technology, it delivers 867Mbps speed rate at 5GHz radio. Come with Gigabit ethernet LAN port design , the maximum throughput test for PtP connection can be up to 450Mbps.

ipMAX--IP-COM TDMA proprietary protocol

ipMAX is IP-COM TDMA (Time Division Multiple Access) proprietary protocol to improve performance and capacity for wireless P2MP outdoor application scenarios.
In outdoor enviroment, the CPE use highly directional antennas to connect to the Basestation from distances that can span several kilometers. the CPE can't sense each other, they become "hidden nodes" and cannot coordinate access to the wireless channel. Thus the Basestation experiences frequent collisions from stations transmitting simultaneously. As the network scales, these collisions build up exponentially, increasing latency and lowering throughput.
With ipMAX, it coordinate all the data transmission and allocates time to active clients to provide greater noise immunity performance when compared to the conventional 802.11 CSMA/CA (Carrier Sense Multiple Access / Collision Avoidance) protocol."

iLink--Auto-bridge Technology Enable it To Easy Setup

iLink is IP-COM proprietary auto-bridge technology, It enables the CPE or basestation in factory default settings connect to each other automaticaly after the device is powered on. It is very useful for the person who is not familiar with network knowledge, especilly for for CCTV surveillance transmission application.

Multiple Application Scenarios

Long-Distance Wireless Connection
One work as AP mode and another work as Station mode to create a long distance wrieless connecton for video surveillance and data transmission.
WISP(Client+Router) Mode
Wirelessly connect to WISP station/hotspot to share Internet to local wireless and wired network.

Professional Outdoor Design

Equipped with IP65 waterproof enclouse and high quality hardware design, iLBE-5AC can work in various weather conditions, such as sunshine, rainfall or extremely low/high temperature environment

Easy to Setup and Manage

iLBE-5AC comes with a centralized management software that helps users easily to manage all the devices in the network from a single PC-CPE Controller.
  • 5GHz 11AC 867Mbps
  • 23dbi directional antenna
  • One Gigabit Ethernet Port
  • IP65 waterproof enclosure
  • 6000V Lightning Protection
  • AP,Station,WISP operating mode supported
Product Information
Model iLBE-5AC
Dimensions 391.5*280*223mm
Deployment Pole Mount
Application Scenarios PtP and PtMP wireless connection for Privated ISP access or CCTV Surveillance
Hardware Features
Frequency Range 5GHz
Compliant Standards IEEE 802.11a/n/ac
Private TDMA Protocol ipMAX
Maximum Wireless Rate 867Mbps
Interfaces 1*10/100/1000Mbps Ethernet Port
Antennas Gain 23dBi
Antenna Beamwidth Horizontal: 10° Vertical: 10°
Reset Button 1
Power Consumption 7.5W
Waterproof Level IP65
LED indicator PoE/LAN,LED1,LED2,LED3
Power Method 24V0.5A Passive PoE
Lightning Protection 6000V
Passive PoE Passive power over ethenet via PoE/LAN (+4,5pins; -7,8pins )
Voltage range: 21-25V DC
Receiver sensitivity 11a 6Mbps -96dBm±1.5dBm
11n MCS7 HT20 -72dBm±1.5dBm
11ac MCS9 HT80 -65dBm±1.5dBm
Software Features
Operating mode AP/Station/WISP/P2MP/WDS Repeater/Router
Enable/Disable Wireless Radio Support
SSID Hidden Support
Wireless Client isolation Support
SSID Isolation Support
Channel Bandwidth 20/40/80MHz
Client Limitation For SSID Support
Wireless Access Control Support
Weak Signal Client Limitation Support
Transmission Power Adjustable power by 1dBm
WMM Capable Support
APSD Capable Support
Wireless Security 64/128 WEP,WPA-PSK,WPA2-PSK,WPA&WPA2-PSK,WPA,WPA2
Transparent Bridge Support
VLAN Tagging for SSID Support
DHCP Server Support
VPN Pass-Through PPTP,L2TP
Remote Web access Support
Schedule Reboot Support
Page Timeout Support
Ping Watchdog Support
Dyndns noip,
Network Diagnoses Ping, Traceroute, Signal Scan
Time&Date Setting Support
Firmware upgrade Support
Backup/Restore Configuration Support
Username Managerment Support
System Log Support
Managed By Controller PC Software -- CPE Controller
Package Contents 1*5GHz 23dBi ipMax AC Gigabit Outdoor CPE iLBE-5ACV1.0
1*PoE Power Adapter
1*Quick Installation Guide
Operating Temperature -30℃ ~ 60℃
Storage Temperature -40℃ ~ 70℃
Operating Humidity 10%~90% non-condensing
Storage Humidity 10%~90% non-condensing
Default login IP
Default Login Username admin
Default Login Password admin
Certifications FCC/CE/RoHS
  • Hardware Version: V1.0

    Software Version: V1.0.0.3

    Upgrade Notes:

    1. This firmware is only fit for iLBE-5ACv1.0 and its firmware version must be in V1.0.0.XX or more.

    2. Do not power off the device when upgrading.

    3. Please unzip the file you downloaded and use the file ended with "bin" or "trx" to upgrade your device.

    4. Please reset it to factory settings after upgraded it.

    Release Notes:

    1. Updated TDMA function.

    2. Compatible with FCC standard and Tx power can set as 26dBm.

  • Notes:

    1. This firmware is only fit for iLBE-5AC and its firmware version must be in V1.0.0.XX or more.

    2. Do not power off the device when upgrading.

    3. Please unzip the file you downloaded and use the file ended with "bin" or "trx" to upgrade your device.

    4. Please reset it to factory settings after upgraded it.


    1.This version compatible with FCC standard.

    2.Upgrade it to enable high output power feature.

    3.The maximum output power value can be set to 26dBm.

  • Applicable model: CPE3(v1.0.0.5 or later)/CPE6/CPE9(v1.0.0.5 or later)/CPE12/BS6/iLBE-5AC
  • 2021-09-13
  • Note: Before download this software, please check the model and firmware version in Managed Device List as below.

    If the model and firmware do not contain in list, it cannot manage your CPE.

    If your current firmware is previous version, please upgrade to latest version.

    Managed Device List: